濟南誠耐金屬制品有限公司

濟南誠耐金屬制品有限公司

不斷發展技術力量、完善的設計服務團隊,真誠為您提供的服務

咨詢熱線
于經理15194166167
15990909037

聯系我們

企業名稱:濟南誠耐金屬制品有限公司

聯系人:于經理

電話: 15990909037

電話: 15194166167

地址:山東省濟南市歷城區小清河南路8288號

當前位置:首頁 »資訊中心 » 常見問題如何識別不規范不銹鋼玻璃門

如何識別不規范不銹鋼玻璃門

來源:http://yippyshippy.com/ 瀏覽:0發表時間:2024-04-08

不銹鋼玻璃門一般無門框,只有上下金屬門夾,或只在角部為安裝軸部分金屬件鉸接的地彈簧來實現。

Stainless steel glass doors generally have no door frame, only upper and lower metal door clips, or only ground springs hinged on the metal parts of the installation shaft at the corners.

1、門扇安裝前,地面地彈簧與門框頂面的定位銷應定位安裝完畢,兩者必須同軸線。安裝時用吊垂線檢查,確保地彈簧轉軸與定位銷的中心線在同一垂直線上。

1. Before installing the door leaf, the ground spring and the positioning pin on the top surface of the door frame should be positioned and installed, and both must be aligned with the same axis. During installation, use a suspension line to check and ensure that the center line of the ground spring shaft and the positioning pin is on the same vertical line.

20220920051136605.jpg

2、安裝玻璃門扇上下門夾:把上下金屬門夾分別裝在玻璃門扇下下兩端,并測量門扇高度。如果門扇的上下邊距門橫框及地面的縫隙超過規定值,即門扇高度不夠,可在上下門夾內的玻璃底部墊木夾板條。如果門扇高度超過安裝尺寸,則需裁去玻璃扇的多余部分。若為鋼化玻璃則需按安裝尺寸重新定制。

2. Install the upper and lower metal door clips on the glass door leaf: Install the upper and lower metal door clips on the lower and lower ends of the glass door leaf, and measure the height of the door leaf. If the gap between the upper and lower edges of the door leaf and the door transom and the ground exceeds the specified value, that is, the height of the door leaf is not enough, wood splint strips can be padded at the bottom of the glass in the upper and lower door clips. If the height of the door leaf exceeds the installation size, the excess part of the glass leaf needs to be cut off. If it is tempered glass, it needs to be customized according to the installation size.

3、固定玻璃門扇上下門夾:定好門扇高度垢,在厚玻璃與金屬上下門夾內的兩側縫隙處,同時插入小木條,輕敲穩實,然后在小木條、厚玻璃、門夾之間的縫隙中注入玻璃膠。

3. Fix the upper and lower door clips of the glass door leaf: Set the height of the door leaf to scale, and insert small wooden strips into the gaps on both sides of the thick glass and metal upper and lower door clips. Gently tap and firmly, then inject glass glue into the gaps between the small wooden strips, thick glass, and door clips.

4、門扇定位安裝:先將門框橫梁上的定位銷用本身的調節螺釘調出橫梁平面2mm;再玻璃門扇豎起來,把門扇下門夾內的轉動銷連接件的孔位對準地彈簧的轉動銷軸,并轉動門扇將孔位套入銷軸上;然后把門扇轉動90度使之與門框橫梁成直角,把門扇上門夾中的轉動連接件的孔對準門框橫梁上的定位銷,調節定位銷的調節螺釘,將定位銷插入孔內15mm左右。

4. Door leaf positioning installation: First, adjust the positioning pin on the door frame crossbeam out of the crossbeam plane by 2mm using its own adjustment screw; Raise the glass door leaf vertically, align the hole position of the rotary pin connector inside the lower door clip of the door leaf with the rotary pin axis of the ground spring, and rotate the door leaf to fit the hole position onto the pin axis; Then rotate the door leaf 90 degrees to form a right angle with the crossbeam of the door frame. Align the hole of the rotating connector in the door leaf clamp with the positioning pin on the crossbeam of the door frame, adjust the adjustment screw of the positioning pin, and insert the positioning pin into the hole by about 15mm.

5、安裝玻璃門拉手:全玻璃門扇上的拉手孔洞,一般在裁割玻璃時加工完成。拉手連接部分插入洞口時不能過緊,應略有松動;如插入過松,可在插入部分裹上軟質膠帶。安裝前在拉手插入玻璃的部分涂上少許玻璃膠。拉手組裝時,其根部與玻璃靠緊密后再擰緊固定螺釘,以保證拉手沒有松動現象。

5. Installing glass door handles: The handle holes on the full glass door leaf are usually processed during glass cutting. When inserting the connecting part of the handle into the hole, it should not be too tight and should be slightly loose; If the insertion is too loose, soft tape can be wrapped around the insertion part. Apply a small amount of glass glue to the part where the handle is inserted into the glass before installation. When assembling the handle, tighten the fixing screws after the base is tightly against the glass to ensure that the handle is not loose.

不僅安裝不銹鋼玻璃門的時候要謹慎,而且購買不銹鋼玻璃門的時候也要多了解不銹鋼玻璃門的知識,掌握了才不會選錯優先產品。

Not only should you be cautious when installing stainless steel glass doors, but also when purchasing stainless steel glass doors, you should learn more about stainless steel glass doors to master and not choose the wrong priority products.