濟南誠耐金屬制品有限公司

濟南誠耐金屬制品有限公司

不斷發展技術力量、完善的設計服務團隊,真誠為您提供的服務

咨詢熱線
于經理15194166167
15990909037

聯系我們

企業名稱:濟南誠耐金屬制品有限公司

聯系人:于經理

電話: 15990909037

電話: 15194166167

地址:山東省濟南市歷城區小清河南路8288號

當前位置:首頁 »資訊中心 » 行業動態不銹鋼門套線包邊的做法

不銹鋼門套線包邊的做法

來源:http://yippyshippy.com/ 瀏覽:0發表時間:2022-03-03
用沖擊電鉆在門四周大洞眼,并插入木楔。
Use an impact electric drill to make a big hole around the door and insert a wooden wedge.
將15厘大芯板(或夾板)靠墻側進行防潮處理(刷光油2遍后在貼珍珠棉)。用釘槍校正固定后,再用鐵釘加固。門套線條打底用9厘夾板。打底夾板外側用實木線條收口。合頁位置加板襯固或封兩層15厘大芯板。
Conduct moisture-proof treatment on the side of 15 cm large core board (or splint) close to the wall (apply pearl cotton after brushing varnish twice). After correction and fixation with nail gun, it shall be reinforced with iron nails. The door pocket line is primed with 9 cm plywood. The outer side of the backing splint shall be closed with solid wood lines. Two layers of 15 cm core plates shall be lined or sealed at the hinge position.
門套與門扇相合之處到進門邊的側面用9厘夾板做止口板,止口深度與門的厚度相同。
9 cm plywood is used as the stop plate from the joint of the door pocket and the door leaf to the side of the entrance door, and the stop depth is the same as the thickness of the door.
面板用白乳膠涂勻后貼于打第大芯板及止口板上,并用不銹鋼蚊釘適當加固。
The panel shall be coated with white emulsion and pasted on the first core plate and stop plate, and properly reinforced with stainless steel mosquito nails.
電梯不銹鋼門套
門套線條寬度一般為60mm—80mm.厚度
The width of door pocket line is generally 60mm-80mm thickness
廚衛門套線條里側用不銹鋼(啞光)線條為宜。
Stainless steel (matte) lines should be used on the inner side of the kitchen and bathroom door cover.
門套及門窗套垂直、水平誤差不超過2mm(2m以上不超過3mm)對角線誤差不超過3mm(2m以上不超過
The vertical and horizontal error of door pocket and door and window pocket shall not exceed 2mm (not more than 3mm above 2m), and the diagonal error shall not exceed 3mm (not more than 2m)
門套兩側墻與門套之間距離在門套線條不能壓住接縫時,宜先用水泥砂漿掛鋼釘封平(用板定模灌漿)干燥后方可封板打第,在門套線條能壓住接縫時可用板封龍骨結構。
When the distance between the walls on both sides of the door pocket and the door pocket cannot press the joint, it is advisable to seal the plate with cement mortar hanging steel nails (grouting with plate fixed formwork) before drying. When the door pocket line can press the joint, the keel structure can be sealed with plate.
單面門套用9厘板打底(凸窗應注意窗簾位置)。其他與雙面門套同。入戶大門可封單邊實木線條門套。
Single sided door pocket shall be bottomed with 9 cm board (attention shall be paid to the curtain position for bay window). Others are the same as double-sided door pocket. The entrance door can be sealed with a single side solid wood line door pocket.
窗套不宜包臺面,臺面用大理石鋪貼(防盜網宜在窗套面板封后制作)。單面門套:在原來有門的基礎上起裝飾作用,不起承受門的力量。
The window cover should not cover the table top, and the table top should be paved with marble (the anti-theft net should be made after the window cover panel is sealed). Single sided door pocket: it plays a decorative role on the basis of the original door, and can not bear the strength of the door.